LITMIR.BIZ

Скачать книгу

has been brought out, and this is an important matter, for if the small negatives are to be used for making enlarged negatives or prints, or lantern slides, there should be very little clear glass indeed even in the deepest shadows of the subject. As a rule it may be said that when every part of the image is at least gray the maximum possible amount of detail has been brought out. If the greyness begins to spread to the margins of the plate where it has been protected by the rebate of the dark slide, general fog is being produced, and, as a rule, little will be gained, but much may be lost, by continuing the development for any considerable time after this is observed. When development is completed the developer is poured off, the plate is well rinsed under the tap or in two or three changes of water, and is then ready for fixing.

      DEVELOPMENT WITH PYRO-AMMONIA.

This method of development has the advantage that the constituents can be kept in concentrated solutions, considerable modifications in the composition of the developer can be made very readily and the negatives obtained are of excellent printing quality. On the other hand it cannot be satisfactorily employed with certain brands of rapid plates, because with them it has a tendency to produce general fog, and with some other plates, especially when they are old, it has a tendency to produce what is known as green fog.

      Three solutions are prepared:—

Reducer.
Pyrogallic acid	1	oz. or	10	parts
Potassium metabisulphite1	1	oz. or	10	parts
Water, to make up to	10	oz. or	100	parts
Accelerator.
Ammonia	1	oz. or	10	parts
Water, to make up to	10	oz. or	100	parts
Restrainer.
Ammonium bromide	1	oz. or	10	parts
Water, to make up to	10	oz. or	100	parts

[1] The metabisulphite is dissolved in about 8 oz. (80 parts) of water with the aid of heat, and the pyrogallic acid is then added. When the liquid has cooled it is made up to 10 oz. (100 parts) by addition of water, the whole being well mixed by shaking.

      For each ounce of developer, take 20 minims of reducer, 20 minims of restrainer and 40 minims of accelerator, and make up to 1 oz. with water. With some plates 60 minims of accelerator and 30 minims of restrainer may be used, but any greater proportion of accelerator has considerable tendency to produce general fog. On the other hand the proportion of restrainer can often be increased with advantage since, unless the amount added is very large, its chief effect is to prevent general fog; 30 minims of restrainer to 40 minims of accelerator, or 40 minims of accelerator to 60 minims of restrainer are proportions that can be recommended. Too low a proportion of bromide should be carefully avoided.

      It is very important to ascertain, by careful trial with each brand of plates that is to be used, what is the maximum proportion of ammonia that can safely be added, and what proportion of bromide to ammonia is necessary in order to prevent general fog. As a rule, the more rapid the plates the smaller is the quantity of ammonia that can be used with safety.

      By far the best plan is to keep development well under control by adding only part of the accelerator at the beginning of development and adding the rest as circumstances require.

      For each ounce of developer take 20 minims of pyro solution and make up to the required bulk with water. In another measure mix for each ounce of developer 40 minims of bromide solution and 60 minims of ammonia solution, and regard this as the maximum quantity that can be added with that bulk of developer. Now to the diluted pyro solution add about a quarter or one-third of the ammonia and bromide solution, pour this mixture on the plate and observe what happens.

      If the mode of appearance of the image indicates that the plate has been correctly exposed, about half the remaining ammonia and bromide mixture may be added to the developer at once, and the action allowed to continue, with occasional rocking of the dish. If development proceeds satisfactorily and, in particular, if the chief details in the shadows begin to appear before the highest lights have become too opaque, it is not necessary nor advisable to add the last portion of the ammonia and bromide mixture, since the tendency to general fog and green fog is reduced when the proportion of ammonia is kept as low as possible. On the other hand, if the development flags and the appearance of shadow detail is a little tardy, the rest of the ammonia and bromide mixture must be added.

      

      If the plate seems to be over-exposed, no more of the ammonia and bromide mixture should be added for some time, until it is seen whether the quantity already in the developer will suffice to complete development. If it seems that the over-exposure has been considerable, a further quantity of pyro solution (10 to 20 minims per oz.) and also of bromide solution (10, 20, or 30 minims per oz.) may be added with advantage. Development is then allowed to continue and the negative is examined from time to time; if it is seen that the opacity does not increase, or if sufficient detail in the deep shadows does not appear, further small quantities of the ammonia and bromide mixture may be added cautiously until the required result is obtained, waiting a little while to see the result of each small addition before adding more.

      

Teasels By Carine Cadby.

      When the plate behaves as if under-exposed, dilute the developer at once with half the quantity or an equal quantity of water, according to the degree of under-exposure indicated, and add the whole of the ammonia and bromide mixture. These modifications should check the rate at which the high-lights of the subject gain opacity, whilst accelerating the appearance of the middle tones and shadows. Should this effect not be produced, further quantities of ammonia and bromide mixture may be added or, in extreme cases, ammonia alone, and the developer may be still more diluted with water.

      If any considerable parts of the image still show no detail, local development with a brush may be tried as a last resource. A soft camel's hair brush, preferably mounted in quill, is used. Some of the ammonia and bromide mixture is placed in a vessel and diluted with two or three times its volume of water. One corner or edge of the plate is raised so that the part to be treated is lifted out of the developer, the diluted ammonia and bromide mixture is applied rapidly with the brush, and the plate is allowed to drop gently back into the developer. The treatment may be repeated if necessary.

      Should all these devices fail, the plate is hopelessly under-exposed.

      Sometimes, when working with a diluted developer as just described, it happens that although all the necessary detail has been brought out, the image gains in opacity very slowly. Provided that all the required detail is visible, small quantities

Скачать книгу