LITMIR.BIZ

      The abrupt changes in the attenuation can be explained by coexisting two attenuation mechanisms. The first mechanism is the effect of the heterogeneous and patchy scCO₂ distribution in the rock matrix, as seen for the intact cores. As assumed by the patchy‐saturation model (e.g., Azuma et al., 2013), pressure in these patches does not equilibrate with the water in the surrounding rock if ultrasonic waves are used for the measurements (i.e., there is no fluid flow across the boundaries). However, with the current, sonic‐frequency measurements, seismic waves cause higher pressure within the stiff, water‐saturated part of the rock, which drives the water toward the softer, scCO₂‐saturated part. With increasing volume of the rock where the two fluids coexist, the overall attenuation of the sample increases as scCO₂ is injected into the sample.

      The second mechanism is the attenuation caused by the interaction between a high‐porosity, high‐compliance fracture and a lower‐porosity, low‐compliance rock matrix. At the initial, water‐saturated state, attenuation in the sample is large. This is because seismic waves induce enhanced pressure changes within the compliant fracture, which drives dynamic fluid exchange with the matrix and dissipates a large amount of energy. This attenuation becomes small once the compliance of the fluid in the fracture increases, and the fracture‐driven motions of the water in the rock matrix diminish.

This reduction is expected to be large if scCO₂ fills the fracture faster than the surrounding matrix, resulting in similar wave‐induced pressures within the fracture and the matrix. As the CT images in Figure 5.9 indicate, this situation appears to be the case in our experiments: fast passing of the fluid is seen along high‐permeability sedimentary layers (Frac IIb test) and the sample‐Mylar interface (Frac IIa test). Figure 5.10 compares the scCO₂ saturations for only the fracture and for the entire core for Frac IIb test. This plot indicates that when rapid changes in the Young's modulus and the attenuation occur (core scCO₂ saturation ~5%–7%), nearly 50% of the fracture is already saturated with scCO₂, although from the CT images, most of the matrix near the fracture is still fully saturated with water. The final saturation of the fracture is also much higher (~83%) compared with the average over the entire core (~17.5%). As more pores near the fracture are invaded by scCO₂, because wave‐induced pore pressure in the matrix also decreases, the attenuation caused by the fluid movement between the fracture and the matrix increases again. Additionally, introduction of scCO₂ in the second half of the core increases attenuation further.

The above effect can be examined semiquantitatively by comparing the changes in the Skempton coefficients of the fracture and the rock matrix during fluid substitution. Under uniaxial stress, assuming an undrained state (i.e., only the “driving force” of the fluid flow is examined here), pore pressure and axial stress in the rock matrix are related by

Figure 5.9 Young's modulus E and its related attenuation a_E compared with the scCO₂ distribution in Frac IIa and Frac IIb cores. The maximum decreases in E occur when scCO₂ reaches the fracture but before the saturation in the adjacent rock matrix becomes high. Attenuation also drops abruptly at the same time. Green boxes indicate the responses due to possible relaxation of the fractures resulting from the invasion of scCO₂. However, the attenuation starts to recover as more scCO₂ saturates the fracture and the rock matrix. Red oval indicates artifacts due to CT image registration errors. Blue oval indicates fast passing of scCO₂ along a Mylar sheet, mimicking the behavior of a highly permeable sedimentary layer or a core‐parallel fracture in the sample: (a) Young's modulus and (b) Young's modulus attenuation.

      (5.13)

Figure 5.10 Comparison between the scCO₂ saturations in Frac IIb sample within only the fracture versus the entire core. The saturation within the fracture was determined from CT images. When rapid changes in the Young's modulus and the attenuation occur in Figure 5.8 (core scCO₂ saturation ~5%–7%), nearly 50% of the fracture is already saturated with scCO₂, although from the CT images, most of the matrix near the fracture is still fully saturated with water. The final saturation of the fracture is also much higher (~83%) compared with the entire core (~17.5%). Note that the second data point in the plot was affected by CT image registration errors near the bottom of the sample.

      where the fractor 1/3 is due to the fact the radial total stresses τ ₁₁ and τ ₂₂ are zero. B can be expressed as (e.g., Mavko et al., 1998)

      (5.14)

      where K _f is the bulk fluid modulus for mixed water and scCO₂. Also, from equations (5.5) and (5.6), by assuming no fluid motion in the fracture (i.e., ),

      (5.15) Скачать книгу