LITMIR.BIZ

Скачать книгу

primary design tool was based on the work of Eppler (1990, 1993), who developed a method of determining the nature of the 2‐D viscous flow around an aerofoil of any profile. The Eppler method includes flow separation in the initial stages of stall and has proved to be very successful.

      In addition, several different aerofoil families have been designed for stall‐regulated, variable‐pitch, and variable‐rpm wind turbines.

      For stall‐regulated rotors, improved post‐stall power control is achieved through the design of aerofoils for the outer sections of a blade that limit the maximum lift coefficient. The same aerofoils have a relatively high thickness to chord ratio to accommodate overspeed control devices.

      For variable‐pitch and variable‐speed rotors, outer section aerofoils have a high maximum lift coefficient, allowing low blade solidity.

      Generally, aerofoil cross‐sections with a high thickness to chord ratio give structural designs of high stiffness and strength without causing a large weight penalty, and aerofoils of low thickness result in less drag.

Table 3.3 Summary of the NREL aerofoils and their applications.

Diameter	Type	Aerofoil thickness	Primary	Tip	Root
3–10 m	Variable speed Variable pitch	Thick	‐‐‐	S822	S823
10–20 m	Variable speed Variable pitch	Thin	S802	S802 S803	S804
10–20 m	Stall regulated	Thin	S805 S805A	S806 S806A	S807 S808
10–20 m	Stall regulated	Thick	S819	S820	S821
20–30 m	Stall regulated	Thick	S809 S812	S810 S813	S811 S814, S815
20–40 m	Variable speed	—	S825	S826	S814
	Variable pitch				S815
30–50 m	Stall regulated	Thick	S816	S817	S818
40–50 m	Stall regulated	Thick	S827	S828	S818
40–50 m	Variable speed Variable Pitch	Thick	S830	S831 S832	S818

      Annual energy capture improvements that are claimed for the NREL airfoil families are of the order of 23–35% for stall‐regulated turbines, 8–20% for variable‐pitch turbines, and 8–10% for variable‐rpm turbines. The improvement for stall‐regulated turbines has been verified in field tests.

      The aerofoil shape coordinates for some of the NREL aerofoils are available on the website of the National Wind Technology Center (NWTC) at Golden, Colorado. Measured aerofoil data for some aerofoils is also available. A licence must be purchased for information about those aerofoils that are restricted.

Some of the NREL large blade aerofoil profiles are illustrated in Figure 3.69.

      3.17.3 The Risø aerofoils

      The Risø National Laboratory in Denmark have also developed families of aerofoil designs for wind turbines with similar objectives to the NREL series (Fugslang and Bak 2004). Although the aerodynamic design techniques of the two laboratories were different, there is, perhaps not surprisingly, a significant similarity about the actual designs.

      The design tools for the Risø aerofoils were the X‐FOIL code developed by Drela (1989), a development of the work of Eppler (1990, 1993), and the Ellipsys‐2D CFD code developed at the Technical University of Denmark by Sørensen (1995).

Three families of aerofoils have been developed at Risø – Risø‐A, Risø‐P, and Risø‐B. The Risø‐A family was designed in the 1990s and was intended for stall‐controlled turbines; however, sensitivity to surface roughness was found to be higher than expected in field tests. The Risø‐A family of aerofoil profiles is illustrated in Figure 3.70 and listed in Table 3.4.

Figure 3.69 NREL aerofoil profiles for large blades.

Figure 3.70 The Risø‐A series of aerofoil profiles.

Table 3.4 The principal characteristics of the Risø‐A series.

Aerofoil	Max t/c %	x/c at max t/c	y/c at TE	Re × 10−6	α ο	cl max	Design α	Design cl	Max cl/cd
Risø‐A1‐15	15	0.325	0.0025 Скачать книгу В начало < 65 66 67 68 69 70 71 72 73 74 > В конец