LITMIR.BIZ

      1

      General Aspects

      1.1 Subjects of the Book

      This book introduces the subject of process analysis, instrumentation and control for modern manufacturing in the plastics industry. Process analysis is the starting point since plastics processing is different from processing of metals, ceramics, and other materials. Plastics materials show an unique behavior in terms of heat transfer, fluid flow, viscoelastic behavior, and a dependence on the previous time, temperature and shear history which determines how the material responds during processing and its end use.

      Many of the manufacturing processes are continuous or cyclical in nature. The systems are flow systems in which the process variables, such as time, temperature, position, melt and hydraulic pressure, must be controlled to achieve a satisfactory product, which is typically specified by critical dimensions and physical properties which vary with the processing conditions. Instrumentation has to be selected so that it survives the harsh manufacturing environment of high pressures, temperatures and shear rates and yet it has to have a fast response to measure the process dynamics. Many times the measurements have to be in a non-contact mode so as not to disturb the melt or the finished product. Plastics resins are reactive systems. The resins will degrade if the process conditions are not controlled. Analysis of the process allows one to strategize how to minimize degradation and optimize end use properties.

Linear systems in which there exists a one-to-one relationship between the input variable and the output response are the easiest to analyze and control. Plastics on the other hand show a nonlinear dependence on part/product cooling which varies with the square of the part thickness, laminar flow which varies with the cube of the wall thickness and mechanical strength/stiffness which varies with the cube of wall thickness. Also, wall thickness influences the crystallization, shrinkage, morphology and critical dimensions of the product.

      In order to make corrections to the process, actuators, also known as final control elements, must introduce energy to the system. This hardware is in the form of servo valves, solenoid valves, servo motors, heaters, and blowers. The sizing, response time, ruggedness and linearity must be considered. All the above hardware has to be assembled into a system and programmed with a suitable algorithm to carry out automatic control. The control configuration and the algorithm are dictated by the system itself. Common control modes are feedback setpoint control which is common in extrusion, servo control which is common in injection molding and blow molding cyclical processes, and combinations and variations thereof.

1.2 Special Issues

      A simplified, practical, and innovative approach to understand the design and manufacture of plastic products in the World of Plastics has been presented (1).

      The information defines and focuses on past, current, and future technical trends. This handbook reviews more than 20,000 different subjects.

      Various plastic materials and their behavior patterns were reviewed. Examples are provided of different plastic products and critical factors relating to them that range from meeting performance requirements in different environments to reducing costs and targeting for zero defects (1).

1.3 Injection Molding

       1.3.1 Cost Estimation in Injection Molding

      Cost and performance estimation are frequently used at the early stages of product development to determine the feasibility and drive critical design decisions. Early cost estimation has been hampered by the unavailability and uncertainty of information.

      Here, cost estimates were derived from a complexity metric as defined by the number of dimensions that uniquely define the part geometry (2).

The cost drivers of manufacturing an injection molded plastic part Cpart are expressed in Eq. 1.1.

[1.1]

      The material cost contribution, Cmat, is very significant, typically 50% to 80% of the total part cost. Tooling and processing costs are also significant cost drivers. The processing cost, Cproc, is dependent on the hourly rate charged for the usage of the injection molding machine as well as the processing yield, yproc, which is the ratio of good parts to the total number of parts produced. The tooling cost, Ctool, is amortized over the estimated production quantity N for the life of the tool.

Eq. 1.2 is an expression for the assembled product cost.

[1.2]

      The m parts that constitute the product include both injection molded and standard purchased parts. The cost of the assembly is the product of the assembly shop hourly rate, Rassy, and the total time required to assemble the m parts constituting the product. Thus, the assembly cost decreases as part-count m decreases. The overhead cost per product COH includes both the shop and the administrative overheads.

      Dimensionality and other critical design variables can be automatically assessed within modern computer-aided design systems throughout the product development process to provide continual feedback regarding tooling, process, and material costs (2).

      The complexity-based models were developed and tested with empirical data for thirty injection molded parts from different suppliers and was found to have a highly significant correlation with mold costs and tooling lead times. Models for estimating material and processing costs and yield at the early stages of design are also developed. The developed methods enable real-time evaluation of the effects of a product design on its tooling cost, tooling lead time, processing costs, and yield at the early stages of design (2).

       1.3.2 Cost Prediction Models

      With the recent evolution of additive manufacturing, accurate cost prediction models are of increasing importance to assist decision-making during product development tasks (3). Estimating the cost is a challenging task in that it requires a vast amount of manufacturing knowledge in which many aspects, from design

Скачать книгу