ТОП просматриваемых книг сайта:
High-Performance Materials from Bio-based Feedstocks. Группа авторов
Читать онлайн.Название High-Performance Materials from Bio-based Feedstocks
Год выпуска 0
isbn 9781119655626
Автор произведения Группа авторов
Жанр Химия
Издательство John Wiley & Sons Limited
The second paper focused purely on adsorbency of a range of Starbon materials [38]. In this case, alginic acid‐based materials were used, with pyrolysis temperatures from 300 to 800 °C, whereas the earlier paper used corn starch‐derived materials. A direct comparison of adsorbency between the A300 used in the 2019 paper and the corn starch‐derived S300 used in the original paper indicates contrasting results in terms of pH dependence (Figure 3.12). This may possibly indicate that the surface chemistry of the S300 and A300 materials is significantly different – perhaps not surprising as there are significant amounts of acidic groups remaining in the A300 material [39] which should not be present in the starch‐derived materials.
What can also be seen is that increasing the pyrolysis temperature of the alginic acid material gives a dramatic increase in adsorbency, with A800 not only being very effective at neutral and slightly alkaline pH values but also losing very little adsorbency over the entire pH range evaluated. This is likely related to the much lower oxygen content and hydrophobicity of the material, meaning that its surface charge is much less affected by pH, but also that hydrophobic effects may be important in adsorbing at least some of the components of the grey water. It was found that the adsorption capacity for A800 was 0.92 g g−1, outperforming the other adsorbents tested (and also silica gel and Norit‐activated carbon) in terms of capacity, and also reaching maximal adsorbency in the fastest time (c. 10 minutes cf. 60 minutes for the other adsorbents tested). The high capacity and rapid adsorption make the A800 material a very promising material for laundry waste clean‐up, giving potential to the reuse of grey laundry water in domestic situations.
Figure 3.12 Comparison of pH‐dependent adsorption behaviour (via COD reduction) of A300 and S300 and of A450 and A800.
Source: Data from Shannon et al. [39].
3.2.4.3 Metal Recovery
Muñoz Garcia et al. [40] have shown that Starbon is an excellent adsorbent for precious metals, in particular, gold. Stirring S800 with an aqueous solution of a range of metals designed to mimic a model waste stream from a platinum group metals mine – Au(III), Pt(II), Pd(II), Ni(II), Cu(II), Ir(II), and Zn(II) – under mildly acidic (HCl) conditions gave remarkable results. Gold (99% adsorption), followed by Pd (>90%) and Pt (>80%) were adsorbed very well, whereas iridium (31%) followed by the others (<10%) were less well adsorbed. This selectivity was also observed even when the solution contained far higher concentrations of the poor adsorbers. Adsorption ability appeared to follow the reduction potential of the metals, with gold being the most easily reduced. This fits with the XPS data that confirmed that the predominant species adsorbed was the M(0) oxidation state, as well as demonstrating an increase in oxidised forms of carbon on the Starbon material. The highest capacity observed for gold was an astonishing 3.8 g Au/g Starbon, well in excess of other adsorbents [41]. Selectivity was explained on the basis of reduction potentials, and data from previous work (albeit under different conditions of solvent and precursor (chloride ions can play a major role in metal speciation)) indicate that the reductive adsorption of other metals with similar reduction potentials is also relatively facile on a Starbon surface [42].
The recovery of arsenic (As) from wastewater has been demonstrated by Baikousi et al. [43] using iron oxide/hydroxide‐modified Starbon. They conducted an in‐depth study of the surface of the Starbon‐S700 material before and after iron adsorption, providing details on the nature of surface sites, and a mechanistic understanding of the As uptake. Potentiometric titration of the S700 shows the presence of two sets of functional groups, one (considered to be carboxylic acids) with a pKa of 2.75. This is slightly stronger than most carboxylic acids, but is in line with carboxylic acid strength, as measured on other carbonaceous surfaces. The second set of functionalities had a pKa of 10.3, and were considered to be phenolic in nature. Such an analysis is consistent with that of Shannon et al. [39] who carried out similar analyses on alginic‐acid‐derived materials (see Section 3.2.4.4), suggesting a reasonable degree of similarity in surface functionality between the two material classes.
Loading iron onto the material involved the adsorption of FeCl3 from ethanol, evaporation, and reduction with aqueous sodium borohydride. This gave nanoparticles of iron on the surface of the Starbon. This led to additional protonatable functionalities at pKa = 3.8 and pKa = 7.3, attributed to carboxylic groups and Fe–OH groups, respectively. The latter are thought to be formed by aerial oxidation of the surface of the Fe nanoparticles.
Adsorption of As from water was then carried out at pH 7, at which the As is present as the neutral HAsO3 species. Maximum loading was found to be 26.8 mg As/g material at pH 7. This is attributed to adsorption solely on the FeOH sites, and accounts for 75% of these sites adsorbing 1 As unit. The Starbon itself adsorbs no As, and the pH dependence of adsorption (which drops off rapidly at higher pH, where both the adsorption sites and the As develop negative charges) is consistent with the suggested mechanism. The adsorption capacity is significantly higher than that found for other metal oxide/clay systems.
3.2.4.4 Adsorption and Release of Bioactives
Shannon et al. [39] investigated the adsorption and desorption of bioactive molecules from alginic‐acid‐derived Starbon compared to activated carbon. The set of molecules studied included two plant growth promoters and two plant growth inhibitors, with a view to developing controlled release technology for horticultural applications (Figure 3.13).
Figure 3.13 Four bioactive molecules studied for adsorption/desorption behaviour. (a) Gibberellic acid, (b) indole‐3‐acetic acid, (c) kinetin, (d) abietic acid. The first three are growth promoters, and the fourth is an inhibitor.
Alginic‐acid‐derived materials carbonised at 300, 500, and 800 °C were investigated alongside an activated carbon. The authors studied the physicochemical nature of the four sorbents using pH drift and Boehm titrations to determine surface functionality and acidity/basicity. They found that pHpzc, the pH at which the surface has net zero charge, was 7.9 for the activated carbon, but started at 6.1 for the A300 material, with the value shifting significantly to higher values for the A500 and A800 materials (8.7 and 9.2, respectively). Combining the adsorption results with Boehm titration indicated that the changes in pHpzc are predominantly due to the partial loss of carboxylic functionality in the alginic acid structure at 300 °C, a process that is complete by 500 °C, where more basic, oxygen‐based, functionality predominates. As discussed in Section 3.2.4.1, the alginate materials contain significant inorganic content, which will increase by a factor of 2 from 300 to 800 °C – this is likely to increase the basic character of the materials as a function