LITMIR.BIZ

       One way to illustrate this principle is to line up 15 balls on a pool table in a perfectly straight line, as shown in Figure 2-2. If you hit the cue ball on one end of the line, the ball on the opposite end of the line will almost immediately move. The other balls will move a little, but not much (assuming you line them up straight and strike the cue ball straight).FIGURE 2-2: Electrons transfer current through a wire much like a row of pool balls transfers motion.This is similar to what happens with electric current. Although each electron moves slowly, the ripple effect as each atom loses and gains an electron is lightning fast (literally!).

       It’s no coincidence that moving water is also called current. Many of the early scientists who explored the nature of electricity believed that electricity was a type of fluid, and that it flowed in wires in much the same way that water flows in a river.

        The strength of an electric current is measured with a unit called the ampere, sometimes used in the short form amp or abbreviated A. The ampere is nothing more than a measurement of how many charge carriers (in most cases, electrons) flow past a certain point in one second. One ampere is equal to 6,240,000,000,000,000,000 electrons per second. That’s 6,240 quadrillion electrons per second. (That’s a huge number, but remember that electrons are incredibly small. To give it some perspective, though, imagine that each electron weighed the same as an average grain of sand. If that were true, one amp of current would be equivalent to the movement of nearly 350 tons of sand per second.)

       Most electric incandescent light bulbs have about one amp of current flowing through them when they are turned on. A hair dryer uses about 12 amps.

       Current in electronic circuits is usually much smaller than current in electrical devices like light bulbs and hair dryers. The current in an electronic circuit is often measured in thousandths of amps, or milliamps (abbreviated mA).

       Current is often represented by the letter I in electrical equations. The I stands for intensity.

       Whenever there’s a difference in charge between two locations, there’s a possibility that a current will flow between the two locations if those locations are connected by a conductor. Because of this possibility, the term potential is often used to describe voltage. Without voltage, there can be no current. Thus, voltage creates the potential for a current to flow.

       If current can be compared to the flow of water through a hose, voltage can be compared to water pressure at the faucet. It’s water pressure that causes the water to flow in the hose.

       Voltage is measured using a unit called, naturally, the volt, usually abbreviated V. The voltage that’s available in a standard electrical outlet in the United States is about 117 V. The voltage available in a flashlight battery is about 1.5 V. A car battery provides about 12 V.

       You can find out how much voltage exists between two points by using a device known as a voltmeter, which has two wire test leads that you can touch to different points in a circuit to measure the voltage between those points. Figure 2-3 shows a typical voltmeter. (Actually, the meter shown in the figure is technically called a multimeter because it can measure things other than voltage. For more information about using a voltmeter, see Chapter 8 of this minibook.)FIGURE 2-3: You can use a multimeter like this to measure voltage.

       Voltages can be considered positive or negative but only when compared with some reference point. For example, in a flashlight battery, the voltage at the positive terminal is +1.5 V relative to the negative terminal. The voltage at the negative terminal is –1.5 V relative to the positive terminal.ARE YOU POSITIVE ABOUT THAT?For the first 150 years or so of serious research into the nature of electricity, scientists had electric current backward: They thought that electric current was the flow of positive charges and that electric current flowed from the positive side of a circuit to the negative side.It wasn’t until around 1900 that scientists began to unravel the structure of atoms. They soon figured out that electrons have a negative charge, and current is actually the flow of these negatively charged electrons. In other words, they discovered that current flows in the opposite direction from what they had long thought.Old ideas die hard, and to this day most people think of electric current as flowing from positive to negative. This concept of current flow is sometimes called conventional current. Modern electronic circuits are almost always described in terms of conventional current, so the assumption is that current flows from positive to negative, even though the reality is that the electrons in the circuit are actually flowing in the opposite direction.

        I’d like to tell you the exact definition of a volt, but I can’t — at least not yet. The definition of a volt won’t make any sense until you learn about the concept of power, which is described later in this chapter in the section titled “Understanding Power.”

        Although current stops flowing when the two sides of the circuit have been neutralized, the electrons in the circuit don’t stop moving. Instead, they simply revert to their natural random movement. Electrons are always moving in a conductor. When they get a push from a voltage, they move in the same direction. When there’s no voltage to push them along, they move about randomly.

       In electrical equations, voltage is usually represented by the letter E, which stands for electromotive force.