AutoCAD For Dummies - Ralph Grabowski

Скачать книгу

in most drafting disciplines.

      Throughout this book, I show AutoCAD running in the Ribbon-based Drafting & Annotation workspace that is present in both AutoCAD and AutoCAD LT. Likewise, I tell you where to find commands and what to select by using the Ribbon.

      

The steps in this chapter, unlike the steps in most chapters in this book, form a sequence. You must complete the steps in order. Figuring out how to use AutoCAD is a little like figuring out how to drive, in which parallel parking comes before Indy car racing, except that with AutoCAD you’re free to stop in the middle of the street and take a break. If things get away from you, press Esc two or three times to terminate any command that’s in progress, and type the letter U and then press the Enter key to undo the last thing you did. Incidentally, U and UNDO are two similar commands and between them are probably the most-often-used commands in AutoCAD.

      

If you find that selecting and editing objects work differently from the way I describe in this chapter, you have (or someone else has) probably changed the configuration settings on the Selection tab in the Options dialog box. Chapter 24 describes these settings and how to restore the AutoCAD defaults.

Snapshot shows how base is my plate.

      FIGURE 3-1: How base is my plate.

      A gray icon indicates that the button’s function is Off, while a light blue icon indicates On. (Your screen might show icons against a dark gray background, but I used a white background for a clearer image on the printed page.)

      You can find the files I use in this sequence of steps at this book’s companion website: Go to www.dummies.com/go/autocadfd19 and download afd03.zip. The Zip file contains imperial and metric versions of the base plate exercise at various stages, and the Read Me file on the Downloads tab describes the files in details.

      

Pay attention to feedback from AutoCAD. Glance at the messages the program sends you after each step via the command line at the bottom of the screen or the Dynamic Input tooltip near the cursor so that you become familiar with the names of commands and their options. If you want to see messages next to the cursor as you use the program, click the Dynamic Input (F12) button on the status bar so that its icon is light blue rather than gray.

      In this first set of steps, you create a new drawing from a template, change a few settings to establish a 1:10 scale (that is, 1 inch on the drawing is equivalent to 10 inches on the real object), and save the drawing:

      1 Start AutoCAD.As indicated in Chapter 1, the startup procedure can vary depending on your version of Windows and how it is set up.

      2 Start a new drawing that uses AutoCAD’s Imperial template.Click the down arrow next to the New button on the Start tab. Don’t click the big New button itself or the New button on the Quick Access toolbar. You must use the down arrow. I explain why in Chapter 4 — humor me for now. Have I lied to you recently?A list of drawing templates (DWT files) appears. Templates in AutoCAD are similar to templates in Microsoft Word and other programs. Chapter 4 describes how and why to create and use custom drawing templates.If the acad.dwt file name is missing from the list, select Browse Templates. In the Select Template dialog box that appears, select acad.dwt, as shown in Figure 3-2. (In AutoCAD LT, select acadlt.dwt.)AutoCAD creates a new, blank drawing that uses the settings in acad.dwt. The acad.dwt template (acadlt.dwt in AutoCAD LT) is AutoCAD’s default, plain-Jane (or should that be plain-Pat to be gender-neutral?) template for creating drawings that use imperial units (units expressed in inches or feet or both). Chapter 4 contains additional information about these and other templates.FIGURE 3-2: Starting a new drawing from a template.

      3 Check your workspace. The workspaces in AutoCAD look similar. To make sure that you’re using the same workspace as I am in this chapter (and in most of this book), click the gear icon, near the right end of the status bar (and shown in the margin). If the check mark in the drop-down list isn’t beside Drafting & Annotation, click Drafting & Annotation.

      4 Set up the initial working environment.Make the following settings: Click all the buttons on the left half of the status bar as necessary until they look gray, except Dynamic Input (F12) and Ortho (F8), which should be blue. Turn the background grid (F7) on or off, your choice.Most beginners seem to like it turned on, and most experienced users turn it off.Some of the other settings can make point selection difficult. Start with them all turned off, and then toggle them on and off as needed. I tell you which ones to use in the remaining steps.

      5 Set the drawing limits that define the working area.Type LIMITS and press Enter.(I explain drawing limits in more detail in Chapter 4.)For now, ignore the Dynamic Input tooltip next to the cursor, and look at the command line. AutoCAD echoes the command name and replies to it. Set the limits of the drawing area by responding to the prompts: Specify lower left corner or [ON/OFF] <0.0000,0.0000>: Press EnterSpecify upper right corner <12.0000,9.0000>: 100,50 Don’t add a space before or after the comma of a coordinate value. It’s the final frontier. If you press the spacebar before you enter the entire coordinate value, AutoCAD will process only the text you've typed.

      6 Display the defined working area.Start the Zoom command.The Zoom command is hidden away on the Ribbon, so it is usually far faster and easier to simply type Z and press Enter.ZOOM Specify corner of window, enter a scale factor (nX or nXP), or [All/Center/Dynamic/Extents/Previous/Scale/Window/Object] <real time>:…Type A and press Enter.AutoCAD zooms so that the screen shows the limits (that is, All)

Скачать книгу