CCNA Routing and Switching Complete Study Guide - Todd Lammle

Скачать книгу

Make sure your remote routers are not connected to the Internet.

      F. If authentication is configured, make sure all routers use different passwords.

      16. You have two OSPF directly configured routers that are not forming an adjacency. What should you check? (Choose three.)

      A. Process ID

      B. Hello and dead timers

      C. Link cost

      D. Area

      E. IP address/subnet mask

      17. When do two adjacent routers-enter the 2WAY state?

      A. After both routers have received Hello information

      B. After they have exchanged topology databases

      C. When they connect only to a DR or BDR

      D. When they need to exchange RID information

      18. Which type of LSAs are generated by ABRs and referred to summary link advertisements (SLAs)?

      A. Type 1

      B. Type 2

      C. Type 3

      D. Type 4

      E. Type 5

      19. Which of the following is not provided by the AH portion of IPsec?

      A. Integrity

      B. Confidentiality

      C. Authenticity

      D. Anti-reply

      20. Which statement about GRE is not true?

      A. GRE is stateless and has no flow control.

      B. GRE has security.

      C. GRE has additional overhead for tunneled packets, at least 24 bytes.

      D. GRE uses a protocol-type field in the GRE header so any layer 3 protocol can be used through the tunnel.

      21. Which QoS mechanism will drop traffic if a session uses more than the allotted bandwidth?

      A. Congestion management

      B. Shaping

      C. Policing

      D. Marking

      22. IPv6 unicast routing is running on the Corp router. Which of the following addresses would show up with the show ipv6 int brief command?

      A. FF02::3c3d:0d: bdff:fe3b:0d80

      B. FE80::3c3d:2d: bdff:fe3b:0d80

      C. FE80::3c3d:0d: bdff:fe3b:0d80

      D. FE80::3c3d:2d: ffbd:3bfe:0d80

      23. A host sends a type of NDP message providing the MAC address that was requested. Which type of NDP was sent?

      A. NA

      B. RS

      C. RA

      D. NS

      24. Each field in an IPv6 address is how many bits long?

      A. 4

      B. 16

      C. 32

      D. 128

      25. To enable OSPFv3, which of the following would you use?

      A. Router(config-if)#ipv6 ospf 10 area 0.0.0.0

      B. Router(config-if)#ipv6 router rip 1

      C. Router(config)#ipv6 router eigrp 10

      D. Router(config-rtr)#no shutdown

      E. Router(config-if)#ospf ipv6 10 area 0

      26. What does the command routerA(config)#line cons 0 allow you to perform next?

      A. Set the Telnet password.

      B. Shut down the router.

      C. Set your console password.

      D. Disable console connections.

      27. Which two statements describe the IP address 10.16.3.65/23? (Choose two.)

      A. The subnet address is 10.16.3.0 255.255.254.0.

      B. The lowest host address in the subnet is 10.16.2.1 255.255.254.0.

      C. The last valid host address in the subnet is 10.16.2.254 255.255.254.0.

      D. The broadcast address of the subnet is 10.16.3.255 255.255.254.0.

      E. The network is not subnetted.

      28. On which interface do you configure an IP address for a switch?

      A. int fa0/0

      B. int vty 0 15

      C. int vlan 1

      D. int s/0/0

      29. Which of the following is the valid host range for the subnet on which the IP address 192.168.168.188 255.255.255.192 resides?

      A. 192.168.168.129–190

      B. 192.168.168.129–191

      C. 192.168.168.128–190

      D. 192.168.168.128–192

      30. Which of the following is considered to be the inside host's address after translation?

      A. Inside local

      B. Outside local

      C. Inside global

      D. Outside global

      31. Your inside locals are not being translated to the inside global addresses. Which of the following commands will show you if your inside globals are allowed to use the NAT pool?

      A. debug ip nat

      B. show access-list

      C. show ip nat translation

      D. show ip nat statistics

      32. How many collision domains are created when you segment a network with a 12-port switch?

      A. 1

      B. 2

      C. 5

      D. 12

      33. Which of the following commands will allow you to set your Telnet password on a Cisco router?

      A. line telnet 0 4

      B. line aux 0 4

      C. line vty 0 4

      D. line con 0

      34. Which router command allows you to view the entire contents of all access lists?

      A. show all access-lists

      B. show access-lists

      C. show ip interface

      D. show interface

      35. What does a VLAN do?

      A. Acts as the fastest port to all servers

      B. Provides multiple collision domains on one switch port

      C. Breaks up broadcast domains in a layer 2 switch internetwork

      D. Provides multiple broadcast domains within a single collision domain

      36. If you wanted to delete the configuration stored in NVRAM, choose the best answer for the Cisco objectives.

      A. erase startup

      B. delete running

      C. erase flash

      D. erase running

      37. Which protocol is used to send a destination network unknown message back to originating hosts?

      A. TCP

      B. ARP

      C. ICMP

      D.

Скачать книгу